Griffon Teppichboden- And Pvc-Boden-Kleber 16.9oz

Description

Griffon Teppichboden- And Pvc-Boden-Kleber 16.9oz
The description of this item has been automatically translated. If you have any questions, please feel free to contact us.
Griffon spray adhesive in a 500ml spray can
Odorless, universal, liquid spray adhesive
Product description
Odorless, universal, liquid spray adhesive based on SBR.
scope of application
For double-sided gluing or short-term fixing of paper, cardboard, felt, fabric, cork, polystyrene foam, polyurethane foam and metal foils as well as for
Surfaces made of wood, hardboard, chipboard, glass, concrete and metal.
Ideally suited for temporary fixing of stencils.
properties
Sticks immediately
Odorless
Universally applicable
Moisture Resistant
preparation
Processing conditions: Do not use at temperatures = + 10 ° C.
Preparation of the surfaces: Clean and degrease the surfaces to be bonded with the Griffon cleaner.
processing
Consumption: 5 m² / liter, to be used on both sides.
Instructions for use
Shake the can well before use.
Temporary fixation
1) Spray the adhesive thinly and evenly onto one of the surfaces from about 25 cm away.
2) Let the glue dry for at least 20 minutes.
3) Put the materials together and press firmly.
Permanent bonding
1) Spray the adhesive thinly and evenly from about 25 cm away on both surfaces.
2) Let the glue dry for at least 20 minutes.
3) Put the materials together and tap, roll or press firmly.
After spraying, hold the spray can upside down and press the spray head until only propellant and no glue is sprayed out. This
prevents the spray head from sticking.
Stains / residue
Wet adhesive residues can be removed with the Griffon cleaner. Dried adhesive residues can be removed mechanically or with a paint stripper.
Please note
The technical data given apply to the basic adhesive without propellant.
Drying times *
Drying / curing time: approx. 20 minutes (fixation); 10 minutes (permanent bonding).
* The drying times can vary depending on the substrate, the amount of product applied, the moisture content and the ambient temperature.
Technical characteristics
Temperature resistance: from -40 ° C to + 50 ° C.
Technical specifications
Basis: styrene butadiene rubber (SBR)
Viscosity: approx. 20 mPa / s
Solid content: approx. 22%
Density: approx. 0.72 g / cm³
Storage conditions
At least 24 months. Limited shelf life after opening. Store in a dry, cool and frost-free place.
Labeling according to Regulation (EC) No. 1272/2008
The product is classified and labeled according to the CLP regulation.
Signal word Danger
Hazardous components for labeling:
Naphtha (petroleum), hydrodesulphurised light, dearomatised
Naphtha (petroleum), hydrotreated light
Naphtha (petroleum), hydrotreated light
n-hexane
Hazard warnings
H222-H229
Extremely flammable aerosol. Container is under pressure: may burst if heated.
H315
Causes skin irritation.
H336
May cause drowsiness and dizziness.
H411
Toxic to aquatic life with long lasting effects.
safety instructions
P101
If medical advice is needed, have container or label ready.
P102
Keep out of the reach of children.
P210
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Do not smoke.
P211
Do not spray on an open flame or other ignition source.
P251
Do not pierce or burn, even after use.
P261
Avoid inhalation of aerosols.
P410 + P412
Protect from direct sunlight. Do not expose to temperatures exceeding 50 ° C / 122 ° F.
P501
Disposal of the contents / the container according to the national regulations
For double-sided gluing or short-term fixing of paper, cardboard, felt, fabric, cork, polystyrene foam, polyurethane foam and metal foils as well as for Preparation of the surfaces: Clean and degrease the surfaces to be bonded with the Griffon cleaner. After spraying, hold the spray can upside down and press the spray head until only propellant and no glue is sprayed out. This Wet adhesive residues can be removed with the Griffon cleaner. Dried adhesive residues can be removed mechanically or with a paint stripper. * The drying times can vary depending on the substrate, the amount of product applied, the moisture content and the ambient temperature. P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Do not smoke. P410 + P412 Protect from direct sunlight
Marke
Griffon
EAN
8710439165929
Material
PVC
Set enthält
PVC-Boden-Kleber
Herstellernummer
6305105
Produktart
PVC-Boden-Kleber